| MONEY SAVING PRODUCTS HOW BI-TRON WORKS ORDER PRODUCTS | ||
 |
Frank Pittorino | |
|
Bi-Tron Product: EP40 Powertrain & Gear Formulation
| |||||||||||||||||||||||||||||
|
Available Sizes:- 5 litre - 20 litre - 75 litre - 200 litre
• Optimises the efficiency of the drive train |
|
What EP40 Powertrain & Gear Formulation Is
Bitron EP40 Powertrain & Gear Formulation is engineered to be compatible with gear oils such as Automatic Transmission Fluid, Mercon & Dexron as well as hydraulic fluids. It is designed to reduce
friction in extreme pressure situations, contributing to a reduction in wear and tear and operating temperatures. Bitron EP40 Powertrain & Gear Formulation coats the metal with a protective layer of
molecules. It will actually be attracted into areas of high wear because the extra friction creates extra heat and so extra negative charge, whereas conventional oil will run away from that area. The reduction in
friction leads to less waste of energy (energy lost in the form of heat & noise). This means that more energy is free to pass through the drive train providing an improvement in horsepower or power output at
the wheels.
Bitron EP40 Powertrain & Gear Formulation is probably one of the more versatile products in the Bitron family. Its uniquely engineered pure hydrocarbon base makes it completely
compatible with a wide range of different gear & bearing oils as well as hydraulic & cutting fluids.
Directions For Use
Initial Treatment:
Add Bitron EP40 Powertrain & Gear Formulation at a ratio of 10% of the volume of the reservoir being treated. Check oil/hydraulic fluid after 1000km-1500km (10-15hrs) and change if
necessary.
Subsequent treatments:
Add Bitron EP40 Powertrain & Gear Formulation at the rate of 5% of the volume of the reservoir being treated with each oil change as recommended by the equipment manufacturer.
The optimum ratio (if in any doubt) is 5% of the overall volume of the casing (not the quantity of oil) being treated. This is the same ratio regardless of how large the case is. The Bitron needs to be reapplied only when the fluid is changed according to the manufacturer’s guidelines.
If unsure of treatment ratios and special applications contact your distributor.
|
Points to note: |
Bitron EP40 Powertrain & Gear Formulation is not compatible with brake fluids and should never be added to brake system master cylinders. It should be noted that many hydraulic clutch systems use brake fluid, not hydraulic oil, and Bitron EP40 Powertrain & Gear Formulation should not be used.
Not suitable for use in wet clutches or brake systems.
Treatment results should include:
1. Smoother, faster shifting of gears in manual and automatic transmissions
2. reduction of transmission gear howl and vibration
3. less torque loss and increase in actual power to the drive train
This product will not cause 'slippage' in either manual or automatic transmissions. On the contrary, its use results in smoother, easier gear changes. Clutches need friction to operate – the clutch plates in an automatic transmission are bathed in transmission fluid but are fibrous in makeup (similar to brake pads) and so should be treated with Bitron. Bitron EP40 Powertrain & Gear Formulation coats and protects the complex systems of metal gears that make up the remainder of any transmissions or gearbox.
Bitron EP40 Powertrain & Gear Formulation will assist in the protection of the automatic transmission or gearbox from friction and reduce the heat build-up which destroys the effectiveness of the fluid (the major cause of failure).
Note: Bitron is non-corrosive and cannot negatively affect the material of the seals or gaskets. It is a metal treatment and treats only the metal surfaces.
Caution: Bitron will not restore damaged seals that are already hardened and cracked.
Differentials, Gears and Transfer Cases
For regular, limited slip or Posi-Trac differentials, gears and transfer cases, mix at 5% Bitron EP40 Powertrain & Gear Formulation by volume. Differentials are subjected to considerable heat and friction due to the loads and stress of gears. Laboratory tests and actual use have proven the Bitron decreases internal oil temperatures in differentials anywhere from 5-20 degrees C. The pressures in these systems are huge and the metal surfaces are subject to severe stresses. Bitron will not interfere with the biting points of these systems but will protect the metal from excessive wear.
Treatment results should include:
1. reduced operating temperatures
2. reduced differential noise (gear howl)
Caution Bitron EP40 Powertrain & Gear Formulation is not intended for gears that have sheared or are on the verge of lock-up, unless this is due to overheating and has not yet resulted in welding.
Manual or Power Steering
Bitron EP40 Powertrain & Gear Formulation is compatible with all steering units. Mix at 5% by volume.
Treatment results should include:
1. Easier steering
2. Increased pump flow in worn or dirty power steering units
3. Increase in life expectancy of unit due to decreased wear.
Note: Bitron is not intended to restore mechanical failure.
Hydraulic systems
Bitron EP40 Powertrain & Gear Formulation is completely compatible with hydraulic oils and should be used at a 5% ratio. It will coat the entire system with a protective layer, reducing operating temperatures and wear. Most of the heat in these systems is generated by extreme pressures. This heat will cause the metal to expand and so increase the level of friction and wear, which will then in turn contribute to the heat further expanding the metal, creating more friction and so on.
Drilling and Machining Equipment
Bi-Tron EP40 Powertrain & Gear Formulation is compatible with most drilling fluids.
Air-Conditioner Compressors
Mix 6% Bi-Tron EP40 Powertrain & Gear Formulation by volume.
Air-Conditioner compressors are a tremendous source of power drawing on engines. Before adding, please check with your service technician for assistance.
There are many other areas where friction
can be a source of problems. Many engineers have used their imagination finding new ways of utilizing the many properties of Bi-Tron. Keep in mind that
Bi-Tron EP40 Powertrain & Gear Formulation can be used wherever friction is found. The rule-of-thumb for mix percentage is 6% by volume. It may be advisable to use up to 10%
when quick response is required.
Product Specification:
| Boiling Point for Component | 32% 153.33ºC (300ºF) @ 760.00 mm Hg |
| Vapour Pressure for Component | 32% 3 mm Hg @ 20ºC (68ºF) |
| Specific Vapour Density Air =1 | 1 |
| Specific Gravity | 1.09 @ 21ºC (69.8ºF) |
| Percent Volatiles | 30-35% |
| Evaporation Rate | Slower than Ether |
| Flash Point: Open Cup | 126ºC (259ºF) |
| Explosion Limit: (Lowest value of Component) | Lower 1% Upper 7% |
| Total Base Number TBN | 4.6 |
RETURN TO PRODUCTS PAGE - CLICK HERE
Thank you for visiting Motor Oil and Metal Treatment
Please feel free to contact us at ENQUIRIES@MOTOROILTREATMENT.COM.AU for more information.
All data gathered on this site is treated as strictly confidential, and is not passed on to any third party.
HOME PRODUCTS PURCHASE FAQ's TESTIMONIALS
ABOUT US CONTACT US SITE MAP
| © 2006 - 2010 Zimms Corner Service Station website by stacpoole internet |